Ultrasonic Flowmeters Eurosonic 2000
Ultrasonic Flowmeters Eurosonic 2000 Electromagnetic Flowmeter Euromag Selangor, Malaysia, Kuala Lumpur (KL), Petaling Jaya (PJ) Supplier, Suppliers, Supply, Supplies | Waterhunt Sdn Bhd

The Eurosonic 2000 flow meter is a fixed installation unit to be used in every industrial application. The Eurosonic 2000 flow meter is based on clamp-on transit-time flow measurement principle. It measures the flow rate of liquid in a pipe from outside of the pipe by using a pair of ultrasonic transducers. In general, the liquid should be full in the pipe, and should contain very little particles or bubbles. Examples of applicable liquids are: water (hot water, chill water, city water, sea water, etc.); sewage; oil (crude oil, lubricating oil, diesel oil, fuel oil, etc.); chemicals (alcohol, acids, etc.); waste; beverage and liquid food, solvents and other liquids. Due to the nature of clamp-on technique, the transducer installation is simple and no special skills or tools are required. Besides, there is no pressure drop, no moving parts, no leaks and no contamination. The system is inherently non-intrusive so that hazardous liquids may be measured without the need of adding further leakage paths to the piping. The Eurosonic 2000 flow meter utilizes our proprietary technologies such as advanced signal processing, low-voltage transmitting, small signal receiving with self-adapting. It also incorporates the latest surface-mounting semiconductors and mini PCB design techniques. The Eurosonic 2000 flow meter has also a built-in data-logger, which allows storage of 2,000 lines of data. The stored information can be downloaded to a PC through its RS232 connection port. The Eurosonic 2000 flow meter also provides digital output such as frequency output or pulsed totalizer output, analogue output and alarm digital output. EUROMAG INTERNATIONAL EUROSONIC 2000 is the state of the art fixed installation Transit Time Ultrasonic Flowmeter. It comes with a complete kit of parts that allow the operator to carry out accurate flow measurements in every possible condition in a very short time.

Transit Time Flow Measurement

The transit time technique uses a pair of transducers each of them sending and receiving a ultrasonic signal through the fluid. When the fluid is flowing, signal transit time in downstream direction is shorter than in upstream direction; the difference between these transit times is proportional to the fluid velocity. EUROSONIC 2000 measures accurately this value and correlates it to the flow rate through the inner pipe diameter.


EUROSONIC 2000 uses non wetted clamp on transducers for ease of installation and removal. Clamp on transducers are magnetically or mechanically installed on the outer surface of the pipe where the flow has to be measured.


The EUROSONIC 2000 is a complete stand alone metering system for measurement of the following liquids.
  • Potable water,
  • Sewage (with limited particle content);
  • Seawater;
  • Wastewater;
  • Discharge water;
Other liquids used in the following industrial applications:
  • Power plants;
  • Heat energy metering;
  • Metallurgy and mines;
  • Petroleum and chemicals;
  • Food and Pharmaceutical
  • Marine Operations;
  • Pulp and paper;

The meter is designed to meet all the needs related to flow metering as well as energy metering.

Flow medium shall be clean or very lightly contaminated by particles or bubbles (less than 10000 ppm and particle size les than 80 μm).


  • Economic, non intrusive, flow measurement.
  • Easy set up and installation;
  • Wide range of pipe sizes and materials;
  • Suitable for lined pipes;
  • Velocity, volumetric and totalized flow;
  • Key pad for easy operation;
  • Data logger;
  • Digital output configurable;
  • Analogue output;

Please leave your enquiry here, we will reply as soon as possible.

*only support gif, jpeg, jpg, png, pdf
Switch To Desktop Version